Why is Hisense tv blinking red light? How to fix that?

Usually, Hisense TVs don’t have that many issues or problems. However, the Hisense TV blinking red light is undoubtedly an issue that many people come across. Now, why does it happen, and can you fix it or not.

Well, Hisense tv blinking red light flashes for several reasons. It can be as simple as going on standby mode or as critical as a faulty power board. As for the fixes, you can just reset your TV, or you will need to replace the power board.

I bet things aren’t obvious to you, right? Don’t worry; I am diving deep into the whole thing in a bit. Just read through the article, and you will get all the information you need.

Why the red light on Hisense tv keeps blinking?

Here’s the thing, there are some serious causes for this issue, and there are some pretty usual causes. The thing you have to do is, determine which is the cause in your case. Without knowing them, you can’t do anything at all. So, let’s get ahead and check them out one by one.

Stuck on standby

Sometimes your tv will just get stuck on standby. This can happen just randomly after using your tv for a while. You may see the red light on the power button blinking in this state, but it won’t respond to your remote control or any of the other functional buttons.

Powerboard failure

This is much more of a serious problem than the other one. This is when your Hisense tv will have internal issues. Any bad capacitor, fuse, or blown-out components can cause the power board to fail.

One of the common causes for a bad power board is swollen caps. Another one is some burnt capacitors. Whatever the case may be, it’s a bit more serious than the other issue, which will also require an expert solution.

LED back array issue

Here’s an issue that is pretty rare but can be a possible cause. In this case, your tv shouldn’t have any issues in functioning normally. But you will notice a red light blinking on the power button at all times. This is where the LED panel may be going through some problems. The fixes to this are also pretty easy, but they can be a bit technical at the same time.

Typically, these three are the only causes as to why you may have a blinking red light on your tv. Once you find out which one of them is causing the issue, you can simply get down to fixing them.

How to fix the problem?

Here’s the thing, solving each of the issues is very straightforward. While some of them are a bit technical and may require some expertise, some are very easy to fix by yourself. Let’s get through them to see how you can fix each of the issues –

Fixing the stuck in standby problem

This is the problem that is pretty easy to fix in your Hisense tv. All you have to do is, reset your tv, and it should fix the issue. Here’s how you can reset your tv to fix the problem.

Unplug your tv from the wall. And keep it that way for about 10 to 15 minutes. After that, press and hold the tv power button for about one minute. Then, plug in your tv and turn it on. This resets the tv, and it should work like before.

Fixing the power board failure issue

If your problem is the malfunctioning power board, you can look at it yourself. Simply take off the back panel of the tv and look for the power board. If you see anything damaged or burnt out, you will need to replace the power board to fix this issue.

Not feeling confident about it? Well, then let a technician do the job. Because, trust me, you don’t want to get into all the technical stuff without any proper knowledge. For the most part, the solution to this problem is to replace the power board.

Fixing LED light array.

Similar to the power board issue, the light array or board on your tv can also go bad. It’s not as serious as the power board, but it still can be very annoying. You just have to remove the LED light panel and replace it with a new one to fix this problem.

Conclusion

In short, the Hisense tv blinking red light is an issue that doesn’t require too much effort. All the fixes and solutions are pretty standard. The good thing is that you don’t need to spend too much money fixing the issues. Also, most of the time, it’s just the standby issue, where you can simply get away with just a reset. So, it all works out quite well.